DroneHiTech.com

  • News
  • Reviews
  • How-To
  • Basics
  • Projects
  • About

Flash SiLabs ESC with BLHeli firmware

  • 8. November 2015
  • /
  • How-To
  • /
  • 5 Comments

If you have an ESC with SiLabs MCU, like the HobbyWing XRotor 10A or T-Motor Air 10A, you can flash it with the BLHeli firmware using Arduino board. I will be using my Arduino UNO for the flashing process. If you have another Arduino board, like the Nano, check the pin outs in the 4way-interface
Continue reading...

  • Arduino BLHeli ESC firmware update SiLabs XRotor

Flashing SimonK with Arduino through the signal wire (1-wire)

  • 1. November 2015
  • /
  • How-To
  • /
  • 4 Comments

In this article I will show you how to flash the SimonK firmware with Arduino through the ESC´s signal wire. Important: in order to do this, the bootloader of the ESC must be enabled. This is the case if you have bought a SimonK preflashed ESC (Afro ESC, DYS SN20) or you have already flashed
Continue reading...

  • Arduino firmware update SimonK

Change the baud rate of HC-05 Bluetooth module

  • 31. October 2015
  • /
  • How-To
  • /
  • 10 Comments

In order to connect a HC-05 Bluetooth module to your flight controller, you should probably change the standard baud rate of the module. I will show you how to do this with your Arduino board. You can also change the password or name of the module. There are different HC-05 modules, but it works with
Continue reading...

  • Arduino Bluetooth HC-05

Flash Cleanflight on CC3D using Arduino

  • 31. October 2015
  • /
  • How-To
  • /
  • 38 Comments

Here you will find how to flash the Cleanflight / Betaflight firmware on your CC3D board using Arduino. You need an FTDI adapter or Arduino board with FDTI chip on it, like Nano v3. Connect your Arduino to CC3D as follow: 5V – 5V, GND – GND, TX and RX to the MainPort on the
Continue reading...

  • Arduino Betaflight CC3D Cleanflight firmware update

FrSky CPPM firmware update with Arduino

  • 31. October 2015
  • /
  • How-To
  • /
  • 20 Comments

In this article I will  describe, how to update the FrSky D8R-II Plus or D4R-II receiver with 27ms CPPM firmware. By using CPPM signal you only need one wire for all channels and not separate wires for every channel. You can buy the FrSky Update Cable or you can use your Arduino board. You can
Continue reading...

  • Arduino D4R-II firmware update FrSky ftdi receiver
Quadcopter Arduino Uno

Quadcopter with Arduino Uno running MultiWii

  • 31. October 2015
  • /
  • How-To
  • /
  • 113 Comments

Here I will show you how to use Arduino Uno as a flight controller for your quadcopter. You will also need all other parts, described in Part I of How to build a  quadcopter. Essential part of every flight controller is the gyroscope/accelerometer sensor. So you need this one too for your Arduino flight controller.
Continue reading...

  • Arduino barometer compass flight controller MultiWii Quadcopter

Languages

  • enEnglish
  • bgБългарски (Bulgarian)

Facebook Page

Facebook Page

Recent Posts

  • T-Motor F60 Pro IV Review and thrust test
  • iFlight DC5 HD – DJI FPV build log
  • Aikon F7 Mini V2 for DJI FPV System
  • DJI FPV quadcopter build log
  • FrSky Taranis X-Lite Transmitter Review
  • DJI introduces the new Matrice 200 Series V2 drones
  • T-Motor F40 Pro III Review

Categories

  • Basics 9
  • How-To 41
  • News 61
  • Projects 12
  • Reviews 78
  • Video 10

Aikon F7 Mini V2 for DJI FPV System

DJI FPV quadcopter build log

DJI introduces the new Matrice 200 Series V2 drones

DJI Student discount for drones

DJI Z30–Industrial grade zoom camera

New drone regulations in Germany

Waterproof bag for DJI Mavic Pro

New DJI Mavic Pro Accessories

Phantom 4 Chinese New Year Edition

DJI Snail Review

Follow me

Privacy & Cookies: This site uses cookies. By continuing to use this website, you agree to their use.
To find out more, including how to control cookies, see here: Cookie Policy

Subscribe

Enter your email to subscribe to DroneHiTech.com and receive notifications of new posts.

Top 7

  • T-Motor F60 Pro IV Review and thrust test
    T-Motor F60 Pro IV Review and thrust test
  • SkyRC Q200–Quattro Battery Charger Review
    SkyRC Q200–Quattro Battery Charger Review
  • Flashing SimonK with Arduino through the signal wire (1-wire)
    Flashing SimonK with Arduino through the signal wire (1-wire)
  • Change the baud rate of HC-05 Bluetooth module
    Change the baud rate of HC-05 Bluetooth module
  • Best 2300kv motor for a 180-210mm quadcopter
    Best 2300kv motor for a 180-210mm quadcopter
  • Flash CC3D with Cleanflight using OpenPilot GCS
    Flash CC3D with Cleanflight using OpenPilot GCS
  • DJI FPV quadcopter build log
    DJI FPV quadcopter build log

Tags

Aikon ArduCopter Arduino barometer battery Betaflight BLHeli BLHeli32 BLHeliS camera CC3D Cleanflight Cobra compass damped light DJI drone DYS EMAX ESC F40 firmware update flight controller Flycolor FPV frame FrSky KISS LiPo LittleBee Motors Naze32 OneShot125 Phantom Pixhawk propeller Quadcopter RunCam Scorpion SG Adventure SiLabs T-Motor Taranis video transmitter XRotor
DroneHiTech Copyright © 2015 · Theme design by Bluthemes